Showing results: 226 - 240 of 820 items found.
-
Weshine Electric Manufacturing Co., Ltd
Insulation is one of the most important constituents of a transformer. Any weakness in the insulation may cause failure of transformer. To ensure the effectiveness of the insulation system of a transformer, it must confirms the dielectric test. But the power frequency withstand test alone can not be adequate to demonstrate the dielectric strength of a transformer.
-
MX Series -
AMETEK Programmable Power, Inc.
The California Instruments MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX22.5, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
-
Meco Instruments Pvt. Ltd.,
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
Power System -
SEICA SpA
The Power System is a test platform conceived to verify and certify the operation of power modules.The complete structure, combining two Multi standard cabinets, is sized to contain all of the resources required for testing: drive/sense modules, power modules and load simulators.In this tester, in addition to strictly perform the requested measurement as per technical specifications, the issues of consumptions and dissipations were taken into account, integrating an Energy Recovery circuit which enables reuse of output energy to supply the system.
-
Amida Technology, Inc.
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
G-0 Series -
Shinken Co. LTD.
The G-0 Series Vibration Test Systems consist of all-round, rugged, high quality vibration generators energy-efficient solid-state PWM power amplifiers, ideally suited to any vibration tests requiring high reliability such as MIL, IEC and JIS standardized tests for aircraft, automobiles, electronic components, electric apparatus and aerospace equipment.
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
K-1000 Resistive/Reactive -
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
XRE -
KEYCOM Corp
KEYCOM develops and manufactures various radar systems to measure and evaluate such functionalities of mass-produced millimeter and microwave radars including in-vehicle radars as transmission power, frequency, antenna beam alignment, distance accuracy, bearing accuracy and receiving accuracy. KEYCOM’s product line includes the Radar Test System (RTS) that measures radar distance accuracy and transmission power, and the Rader Alignment System (RAS) that assists you to adjust the mounting position of the in-vehicle radar.
-
Beehive Electronics LLC
Beehive Electronics designs custom high power RF filters used in vacuum coating systems. Our experience spans from kilohertz to gigahertz and power levels up to 50 kilowatts. We provide a turnkey solution: we design, build, and test the filters to the customer's specification.
-
MTL 15 | VP 700006 -
Maschinenbau Haldenwang GmbH & Co. KG.
The MTL 15 test container works completely independently thanks to the optionally available, fully integrated power generator. Equipped with a hydraulic set-down device including cable remote control, the test system can be set up within 15 minutes and is therefore ideal for changing locations.
-
F6150sv -
Doble Engineering
The Doble F6150sv is your versatile solution for testing IEC 61850-based protection devices and schemes.This power system simulator performs the simplest through the most complex tests. The F6150sv has the highest output current of any test set on the market all within a single box.
-
8652A -
Spanawave Corporation
The Spanawave/Giga-tronics 8652A Dual Channel Universal Power Meter has the extensive measurement capabilities and features you need to test today's sophisticated communications systems faster, easier and more accurately.
-
8651A -
Spanawave Corporation
The Spanawave/Giga-tronics 8651A Single Channel Universal Power Meter has the extensive measurement capabilities and features you need to test today's sophisticated communications systems faster, easier and more accurately.
-
NI
PXI Programmable Power Supply modules feature multiplechannels that you can combine for higher voltage or current capabilities. Some modules include isolatedchannels and an output disconnect functionality that allows isolation from the device under test(DUT) when not in use and remote sense to correct for losses in system wiring. You can use these models to simplify the task of designing automated test systems for a wide range of applicationsfrom aerospace and defense to automotive and component testby eliminating the need to mix multiple instrumentation form factors in a given test system.
